Interesting. I’m not seeing my instance in there at all.
Interesting. I’m not seeing my instance in there at all.
How can you check to see if your instance is federated with them?
The mesh ends up being pretty similar every time, showing that the right side of the bed is lower than the left. The concern is that, when printing after auto leveling, the nozzle is far too close on the right side, causing first layer issues, but all is well on the left. It’s almost like the printer believes that the nozzle is further from the bed than it actually is, but only on one side.
I found that the bolts holding the gantry to the base had come loose slightly, and tightened them. That seemed to help a bit, but the issue is still there. I was going to try leveling the x gantry, but I’m still trying to figure out how to do so.
I did some research and was able to pull the mesh. I put it into a visualizer and found that the right side is definitely incorrect (as it matches with the “too low” behavior that I’m seeing. I tried to copy the image here, but Sync won’t let me, but here’s the values.
0 1 2 3 4 5 6 7 8 9 10 11 12
0 +0.03500 -0.02855 -0.09156 -0.15566 -0.22250 -0.29867 -0.38125 -0.45758 -0.51500 -0.54590 -0.55844 -0.56363 -0.57250
1 +0.01869 -0.01856 -0.05355 -0.09305 -0.14383 -0.21602 -0.30324 -0.38746 -0.45064 -0.48415 -0.49888 -0.50610 -0.51707
2 +0.00234 -0.00695 -0.01215 -0.02553 -0.05938 -0.12765 -0.22023 -0.31329 -0.38297 -0.41951 -0.43676 -0.44629 -0.45969
3 -0.01393 +0.00144 +0.02248 +0.03217 +0.01352 -0.05072 -0.14723 -0.24723 -0.32193 -0.36066 -0.37977 -0.39103 -0.40621
4 -0.03000 +0.00178 +0.04016 +0.06533 +0.05750 -0.00240 -0.09922 -0.20143 -0.27750 -0.31633 -0.33563 -0.34711 -0.36250
5 -0.04428 -0.00747 +0.03596 +0.06615 +0.06324 +0.00837 -0.08337 -0.18082 -0.25285 -0.28864 -0.30564 -0.31512 -0.32836
6 -0.05734 -0.02364 +0.01604 +0.04376 +0.04156 -0.00781 -0.09062 -0.17835 -0.24250 -0.27303 -0.28596 -0.29184 -0.30125
7 -0.07236 -0.04528 -0.01310 +0.00888 +0.00535 -0.03877 -0.11166 -0.18823 -0.24340 -0.26810 -0.27650 -0.27838 -0.28352
8 -0.09250 -0.07094 -0.04500 -0.02781 -0.03250 -0.07238 -0.13719 -0.20465 -0.25250 -0.27246 -0.27719 -0.27582 -0.27750
9 -0.11980 -0.10205 -0.08041 -0.06654 -0.07207 -0.10913 -0.16849 -0.22982 -0.27275 -0.28955 -0.29183 -0.28831 -0.28770
10 -0.15219 -0.13878 -0.12196 -0.11197 -0.11906 -0.15424 -0.20929 -0.26559 -0.30453 -0.31884 -0.31920 -0.31399 -0.31156
11 -0.18660 -0.17777 -0.16597 -0.16010 -0.16902 -0.20270 -0.25387 -0.30559 -0.34092 -0.35300 -0.35165 -0.34493 -0.34090
12 -0.22000 -0.21563 -0.20875 -0.20688 -0.21750 -0.24949 -0.29656 -0.34348 -0.37500 -0.38473 -0.38156 -0.37324 -0.36750
The bed leveling is done with the bed and nozzle preheated to printing temp. As for the probe, it’s the stock probe on the Ender 3 Max Neo.
The interesting part is the heat soak. I typically heat it and then only wait a minute or two. I’ll let it sit for a while and try again.
How do you edit, or even view, the map that’s built?
There’s a test pad on the PCB labeled “LT” (left trigger). I used that and compared it’s resistance to ground to that of the right trigger’s test pad. I got about 6-10k ohms on the working one (right trigger), and 3.9-4.4 on this one.
It has 3 pins, and I found that it’s a linear (B), 10k ohm (130, as you said), potentiometer. I found similar ones, but the 9 and 5 at the top concern me. The others that I found have a 60 and a 6 there instead.
I mostly do my own work, but whenever I do take my car to the local Mazda dealer, they always provide a full inspection report as well as a video of the tech checking everything and explaining anything that they’ve found. Even when my wife takes her car in for only basic maintenance (it’s still under warranty so we take it in for oil changes), they do the same thing and don’t charge anything extra.
Same dealer network owns the local Ford dealer and I ended up taking my old Fiesta ST there for an oil change as I didn’t have the space to do it myself at the time. $45 for an oil change and tire rotation, and I got the same inspection report and video.
A while ago, there was something that showed the higher failure rate of various components on EVs because of the lack of routine service that has cars have. Basically, gas cars get a service and inspection every 5-10k miles when the oil is changed and any worn bearings, bushings, etc. are found. EVs don’t have that so things go unnoticed until they fail. Could this be the same? Could the “reliability” concerns just be normal wear that isn’t getting caught since there are no routing inspections?
Is this only in certain areas? YouTube is still working fine for me on FireFox.
It’s not an employee benefit. It’s a membership thing that customers can sign up for. It was literally the only perk of it.
Why’s that? I’m relatively new to ebikes and curious why I’ve seen this opinion around. I have a Lectric XP 2.0 with a hub motor and have no complaints.
Yeah they’re definitely getting up there in price. I had a 2019 and then my company went completely remote in 2020. Ended up finding a clean, low mileage NA and sold the ND to buy it. Haven’t looked back.
I hope you’re able to get an NA as they are so much fun, but a Miata is a Miata and they will all bring a smile. NBs and NCs are getting cheap right now. You can always use one as a stepping stone too.
Looks like I’m finally switching to Firefox.
Actually no, from what I understand. You can install it, just most businesses don’t allow it because they offer no support for it. There are other companies that partner with LibreOffice to offer enterprise solutions though.
I would love if we could use LibreOffice, but our application just doesn’t work with it and our devs won’t even look at it.
I provide support for a Windows-only application that has to do automated document conversion. Some customers refuse to pay for an additional Office license and the only other option is WordPad. Going back to work on Tuesday is going to suck.
I have a Moto G Stylus 2023 (non-5G) and did not receive this notification.
Edit: I never used the Device Help app so it’s not setup. I wonder if this is why I didn’t receive it.
Microsoft purchased Blizzard.