I like Antenna Pod for this - my BT connections let me use the Forward 30 Seconds feature when m driving or running. Since most ads are 30 seconds long, I can cruise through them easily.
Writer, teacher, data driven humanist. Tech geek, model builder, mini-painter, reader. He/Him.
I like Antenna Pod for this - my BT connections let me use the Forward 30 Seconds feature when m driving or running. Since most ads are 30 seconds long, I can cruise through them easily.
It is by will alone I set my mind in motion.
It is by the juice of sapho that thoughts acquire speed, the lips acquire stains.
The stains become a warning.
It is by will alone I set my mind in motion
I moved from a major metro area to middle of forking nowhere several years ago. I kept my library cards from the metro area, which still work for Libby ebook and magazine downloads, while the local rural library is tied into a regional system for the occasional dead tree book.
Fair point, and thank you. Let me clarify a bit.
It wasn’t my intention to say ChatGPT isn’t helpful. I’ve heard stories of people using it to great effect, but I’ve also heard stories of people who had it return the same non-solutions they had already found and dismissed. Just like any tool, actually…
I was just pointing out that it is functionally similar to scanning SO, tech docs, Slashdot, Reddit, and other sources looking for an answer to our question. ChatGPT doesn’t have a magical source of knowledge that we collectively also do not have – it just has speed and a lot processing power. We all still have to verify the answers it gives, just like we would anything from SO.
My last sentence was rushed, not 100% accurate, and shows some of my prejudices about ChatGPT. I think ChatGPT works best when it is treated like a rubber duck – give it your problem, ask it for input, but then use that as a prompt to spur your own learning and further discovery. Don’t use it to replace your own thinking and learning.
There was a story once that said if you put an infinite number of monkeys in front of an infinite number of typewriters, they would eventually produce the works of William Shakespeare.
So far, the Internet has not shown that to be true. Example: Twitter.
Now we have an artificial monkey remixing all of that, at our request, and we’re trying to find something resembling Hamlet’s Soliloquy in what it tells us. What it gives you is meaningless unless you interpret it in a way that works for you – how do you know the answer is correct if you don’t test it? In other words, you have to ensure the answers it gives are what you are looking for.
In that scenario, it’s just a big expensive rubber duck you are using to debug your work.
I’m printing PLA+ at 200C nozzle, 60C bed temp. It’s been fine so far with a few failures I’ve filed under “User Error”.
OK, now I’m curious how I change the bed temp settings after the first layer – something in the slicer? I’m using Ultimaker Cura, and have just recently been digging into the advanced settings.
I’d heard about needing to keep the filament dry, but it hasn’t been an issue for me yet. That said, I’ll get what filament isn’t still sealed into a dessicant loaded container ASAP - thanks!
Heat is ~28C outside (90F or so), more in the shed. I’ve no ABS since I’ve I read it’s tough to work with and I haven’t had an application for it yet. I just did a cleaning on the plate, and I’ll see if that makes a difference.
OK, good to know – just did an alcohol/dish soap wipe and restarted the print, will check it in a bit, and do the cleaning after every print.
Not just parents – my wife has an unhealthy mobile game addiction. We’ve talked about it and talked about it, but it’s still a heavy draw for her.
Same here, never had any problem.
Way-neet Joo-are-ease
OK, so no to pulling it all off.
I’ll give this a try, but let’s say I put the filament in the printer cleanly – the filament won’t be tight for long as it gets pulled into the printer, so what’s to keep it from jamming itself up again?
UPDATE: I really need to learn to try things before I start complaining they won’t work.
I followed your advice – as I was tightening up the windings, it became clear that the lead winding was under the next one. I know I wasn’t the most careful when I initially loaded it, so you’re diagnosis was probably correct.
So I pulled the tangle out, cut off the damaged section of PLA, and more carefully reloaded the filament this time. It seems better now – the filament is feeding better now. Time will tell – I’ll post an update when this print either completes or fails.
One thing I’ve found after printing on my Anycubic Photon Ultra for a while is that I rarely need the .010 - .040 layer heights. I do most of my figures for display, not gaming, and I just don’t see that much distortion from layer lines, or difference when printing at different layer heights. Voxels are a much bigger issue IMO, and I spend a lot more time and effort in getting anti-aliasing set right.
Right now I want something with a higher resolution (the Ultra is only 720P IIRC) and better anti-aliasing – even with it dialed in on Chitubox, I have to do some sanding and filling on smooth surfaces.
…there is a big, big difference between calling someone homeless/addict or saying “experiencing homelessness/addiction”
I agree with this – my point in bringing this up was to highlight the differences in the language we use and the images and ideas those words conjure in the reader/listener. Your experiences are much more direct than mine, and I appreciate the insight.
… I don’t think the author intended to degrade people with their wording. … I think we do a disservice to the people directly suffering from homelessness/addiction/mental health by misdirecting our frustrations towards the journalists increasing awareness of the problem.
I see your points. However, had the director of the facility also used the term “homeless”, I would have never posted this. Its the changing of the word from what was said to what was written that gave me pause.
On the other hand, you have also given me some other ways to think about this story and how it was presented. Thanks for forcing me to confront some of my biases.
I tried KMail and Organizer for a few weeks, but they kept losing connection with Gmail. My calendar would get out of sync, and they only way to fix it was to reset the connection and redo all the appointments.
I’m sure it was user error, since I couldn’t figure it out after spending a couple hours on it, so I just dropped back to webmail and not leaving the mail tab open all day.