And the power panic resume didn’t work :(. This was also my first try at manually changing filaments for multiple colors, waste of effort and filament lol.

  • elscallr@kbin.social
    link
    fedilink
    arrow-up
    7
    ·
    1 year ago

    Get a cheap APC battery backup, for a little over $100 you can get a 1000VA backup that’ll keep your printer running for a few hours through an outage.

    • poofy_cat@lemm.eeOP
      link
      fedilink
      English
      arrow-up
      4
      ·
      1 year ago

      Ended up moving the little 500VA UPS from my computer to the 3D printer. Hopefully it’ll help for brief blips.

  • phx@lemmy.ca
    link
    fedilink
    English
    arrow-up
    5
    ·
    1 year ago

    What’s your method for changing filaments. I’ve not had much luck with doing so

    • poofy_cat@lemm.eeOP
      link
      fedilink
      English
      arrow-up
      4
      ·
      edit-2
      1 year ago

      This model was set up for it already in the .3mf file. It stops, moves the toolhead over, automatically unloads the filament, and waits for me to yank it the rest of the way out then stick in another color. It then purges the nozzle a bit to get the main color fully flowing and asks you if it’s correct before proceeding. I did this like 7 times for this stupid half-failed box lol.

      Edit: Also, you can left-click the plus sign on the layer slider at any height you want after slicing in PrusaSlicer to add manual color changes in.

    • kek_w_lol@lemmy.one
      link
      fedilink
      English
      arrow-up
      2
      ·
      edit-2
      1 year ago

      In prusaslicer, you can set a color change. Or you can edit gcode by hand with the m600 command iirc. But the second way is not recommended

    • CmdrShepard@lemmy.one
      link
      fedilink
      English
      arrow-up
      1
      ·
      1 year ago

      I’ve done it once so far with good results. Setup a color change in Cura and then when that layer comes, the extruder moves to the corner where you unload and reload the filament and then purge it manually. Finally remove any stringing bits and resume the print immediately.

  • Gorroth@lemmy.world
    link
    fedilink
    English
    arrow-up
    4
    arrow-down
    1
    ·
    1 year ago

    That printbed looks huge! What printer is that and how big is that bed?

    I recently was dumb enough to tell Alexa to power off the smart plug of my printer. 5 hours into that print… While I was looking at it printing… huge brainfart… After that I looked into the void for 20mins thinking about how dumb I am…

    • poofy_cat@lemm.eeOP
      link
      fedilink
      English
      arrow-up
      3
      ·
      1 year ago

      This is just a regular-sized Prusa MK4, 250 x 210mm xy build area. I made this custom magnetic G10 sheet for printing PETG, it’s 253.8 x 241mm.

      • Gorroth@lemmy.world
        link
        fedilink
        English
        arrow-up
        1
        ·
        1 year ago

        Ah okay! Nice! Did you have to change something other than the bed to make use of its size (on the hardware)?

        • poofy_cat@lemm.eeOP
          link
          fedilink
          English
          arrow-up
          2
          ·
          edit-2
          1 year ago

          Nope, this is the same size as the stock Prusa sheets. The sheets are all a little bigger than the actual build area.